收藏本站
DATASHEET
5.0mm Infrared LED
IR323
Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.
?
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4.
Cleaning
?
?
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5.
Heat Management
?
?
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6.
ESD (Electrostatic Discharge)
?
?
?
?
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of
friction between LEDs during storage and handing.
7.
Other
?
?
?
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
8
www.everlight.com
:3
Revision Copyright ?
LifecyclePhase:
No: Release
2010, Everlight All Rights Reserved. Release Date : MAY.23.2013. Issue DIR-0000934 Date:2013-05-28 13:04:37.0
Expired Period: Forever
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
IR333-A LED IR 5MM GAA1AS BLUE TH
IR333C/H0/L10 LED IR 5MM GAA1AS BLUE TH
IR383 LED IR 5MM GAA1AS BLUE TH
IR42-21C/TR8 LED IR SUBMINI 1.8MM ROUND SMD
IR533C LED IR SMD GAA1AS WATER CLEAR
IR67-21C/TR8 LED IR TOP GAA1AS WATER CLR SMD
IR7373C LED IR 5MM GAA1AS WATER CLEAR
IR7393C LED IR 5MM GAA1AS WATER CLEAR
相关代理商/技术参数
IR323/H0-A 功能描述:LED IR 5MM GAA1AS BLUE TH RoHS:是 类别:光电元件 >> 红外发射极 系列:- 标准包装:1,200 系列:- 电流 - DC 正向(If):100mA 辐射强度(le)最小值@正向电流:27mW/sr @ 100mA 波长:940nm 正向电压:1.6V 视角:40° 方向:顶视图 安装类型:通孔 封装/外壳:径向 包装:带卷 (TR)
IR3230SPBF 功能描述:马达/运动/点火控制器和驱动器 3-Phase DC CTRL 50 KHz PWM E-Bike RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
IR3230STRPBF 功能描述:马达/运动/点火控制器和驱动器 3-Phase DC CTRL 50 KHz PWM E-Bike RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
IR323-H0-A 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Infrared LED , T-1 3/4
IR32A00000 制造商:未知厂家 制造商全称:未知厂家 功能描述:DIGITAL TEMPERATURE & PROCESS CONTROLLERS
IR32A7LR20 制造商:未知厂家 制造商全称:未知厂家 功能描述:DIGITAL TEMPERATURE & PROCESS CONTROLLERS
IR32BC 制造商:SGX Sensortech 功能描述:Series 3 Hydrocarbon IR Sensor - uncertfied, Bulk
IR32CTQ030 制造商:International Rectifier 功能描述: